Претрага

Упит dcterms_subject_txt:Hierarchical cluster analysis

750 items

  • The optimization of auxiliary machinery in open-cast lignite mines: a case study of bulldozers

    Dragan Ignjatović, Predrag Jovančić, Stevan Đenadić, Ivan Janković, Ivica Ristović (2019)
    One of the most important prerequisites for the successful operation of the open-cast lignite mine is to carry out all the auxiliary works timely with the necessary quality. The most important and most commonly used auxiliary machines are bulldozers. Engaging time of bulldozers use is in direct relation with the coefficients of the time and capacity utilization of the continuous system for the excavation of coal and tailings, which indicates their importance. More than 100 bulldozers have been hired ...
    open-cast coal mine, auxiliary works, bulldozers, optimization, availability
    ... 50% of all auxiliary equipment costs. This implies the necessity for detailed analysis ог all parameters of these machines, including. current and historic trends, as well as some technical capabilities. Such ап analysis would enable better forecasting ог their operation. Dozer's life оп the open-cast ...
    ... Parameters impacting these costs are: type of job performed, costs of fuel and lubricants, transportation cost from manufacturer, interest rates, etc. Analysis was performed according to recommended method for evaluation of hourly ownership and operational costs, including data on auxiliary machines (Caterpillar ...
    ... availability coefficient ој БиПаогет САТ D8R тп Kolubara basin during ј1751 ten years of operation This diagram (Figure 7) is used for further analysis related to optimal replacement time. Lower limit of availability for dozer replacement is 0.80. This is limit value for linear correlation of time ...

  • Geotechnical Conditions for Construction of Savski Trg Metro Station as a Part of the Belgrade Metro Line One

    Nemanja Stanic, Dragoslav Rakic, Josip Isek, Slavoljub Simic (2024)
    In order to solve serious traffic congestion in Belgrade, a number of studies regarding the Belgrade Metro construction have been carried out since 1973. However, only in 2019, the routes of the future metro lines 1 and 2 were de-fined as a part of the General Metro Construction Project. The lines are de-signed to intersect at the location of Sava Square, where an interchange met-ro station will be built. It represents a complex geotechnical structure consist-ing of three different ...
    metro station, geotechnical modelling, displacements

  • Ocena zaštitne funkcije povlatnih slojeva izvorišta Jasik (Opština Batočina) primenom GLA metode

    Rastko Petrović, Igor Jemcov, Dušan Polomčić (2014)
    U cilju utvrđivanja rezervi podzemnih voda i analize uslova zaštite u periodu 2012. i 2013. godine, sprovedena su detaljna hidrogeološka istraživanja na području izvorišta Jasik (opština Batočina). Uspostavljen je sistem monitoringa, čiji je rezultat predstavljao prikupljanje detaljnih hidrogeoloških podataka. Za potrebe analize, izrađen je hidrodinamički model, na osnovu koga je simulirano kretanje podzemnih voda, odnosno, utvrđene zone sanitarne zaštite. Pored navedenog, za potrebe utvrđivanja uslova zaštite podzemnih voda, bilo je neophodno utvrditi podložnost aluvijalne izdani izvorišta Jasik zagađenju. Polazeći ...
    Izvorište Jasik, GLA metoda, zaštita podzemnih voda

  • Investigation of quantitative indicators of anisotropy based on longitudinal elastic waves propagation velocities with uncertainty

    Miloš Gligorić, Jelena Majstorović, Suzana Lutovac (2018)
    ... mean KAj,mean 12 Gligorić M., Majstorović J., Lutovac S. Statistical analysis of the obtained results for isotropic and anisotropic samples is presented in the Table 1 and Table 2. Table 1 Statistical analysis of the obtained results for isotropic samples Statistical parameter 𝐷𝐼𝑖 ...
    ... illustrates obtained results and discussions in relation to our investigations represented at Figures 1-6. Also, brief description of statistical analysis is shown in this section. Finally, Section 6 explains the conclusion of our study. 2 BASICS OF INTERVAL NUMBERS The devices for measuring ...
    ... 55 27.83 Range 6.79 8.25 3.53 6.51 15.11 8.36 StDev. 1.76 2.14 1.76 3.26 3.92 4.21 CV 0.32 0.54 0.12 0.19 0.52 0.15 Table 2 Statistical analysis of the obtained results for anisotropic samples Statistic. param. 𝐷𝐴𝑖,𝑚𝑎𝑥 % 𝐷𝐴𝑖,𝑚𝑖𝑛 % 𝐷𝐴𝑗,𝑚𝑎𝑥 % 𝐷𝐴𝑗,𝑚𝑖𝑛 % 𝐾𝐴𝑖,𝑚𝑒𝑎𝑛 ...

  • Groundwater gravitational circulation of Karst Veliko Vrelo and Malo Vrelo springs by isotope and the noble gas method: case study of the Beljanica Massif

    Ljiljana Vasić, Laszlo Palcsu, Huang Fen (2019)
    Earth-Surface Processes, Geology, Pollution, Soil Science, Water Science and Technology, Environmental Chemistry

  • The application of ArcGIS for assessing the potential of solar energy in urban area: The case of Vranje

    Boban Pavlović, Milica Pešić-Georgiadis (2019)
    In order to determine the solar energy potential for a specified location, it is crucial to consider the latitude, altitude, slope, terrain morphology, atmospheric conditions, etc. Such a complex calculation and mapping of solar energy can be done using the ArcGIS geoprocessing tool, named Area Solar Radiation (ASR). By using the ASR tool, supported with the adequate input data, it is possible to calculate the maximum solar radiation energy (irradiation) for a defined area and for a specified time ...
    Obnovljivi izvori energije, potencijal solarne energije, GIS, mapiranje solarnog potencijala
    ... lation (Fu P., Rich P.M., 2000). Basically, two types of analysis can be distinguished within the SAT. The first one involves the analysis of a specific area, named "Area Solar Radiation" (ASR), and the second one, is for the analysis of the specific points determined by the x and y coordinates ...
    ... changes in the major part of Europe. Polygonal entities represent a state of land cover differentiated in 44 classes, divided into a 3-level hierarchical classification system (Stojkovic S., 2017). The COPERNICUS website includes CLC datasets for different years with the corresponding land cover ...
    ... and the average for a total urban area is 1,227 kWh/m?, annually. The obtained result can be used as an input for further technical and economic analysis of the cost-effectiveness of the usage of solar energy. The presented methodology can be applied to any other area with an appropriate digital ...

  • Using Query Expansion for Cross-Lingual Mathematical Terminology Extraction

    Velislava Stoykova, Ranka Stanković (2018)

  • Curcumin nanonization using an alternative small-scale production unit: selection of proper stabilizer applying basic physicochemical consideration and biological activity assessment of nanocrystals

    Ines Nikolić, Jelena Antić-Stanković, Dragana Božić, Danijela Ranđelović, Bojan Marković, Dominique Jasmin Lunter, Aleksandar Kremenović, Miroslav Savić, Snežana Savić (2020)
    As the number of poorly soluble drugs is increasing, nanocrystals have become very interesting due to wide range of application possibilities. Curcumin was used as a model active ingredient in this work. Even though it has many proven positive effects, due to its physicochemical issues, its possibilities have not been fully exploited. The goal of this work was to select optimal conditions for a top-down method for curcumin nanosuspension production, and to perform their comprehensive characterization applying complementary methodologies: ...
    nanocrystal, curcumin, top-down method, wetball milling

  • Structure, interaction with biomolecules, and cytotoxicity of copper (II) complexes chelating some Schiff base ligands

    Aleksandar Mijatović, Angelina Z. Caković, Aleksandar Lolić, Olivera Klisurić, Marko N. Živanović, Dragana S. Šeklić, Snežana Sretenović, Marija Ilić, Jovana Bogojeski (2023)
    Cancer remains one of the world's deadliest diseases, claiming many lives each day. Transition metal complexes are leading candidates in developing anticancer agens with cisplatin used in chemotherapy worldwide. Copper, an endogenous metal in the human body, is especially attractive because of its typical redox biological activities and a relatively strong affinity to nucleobases. A series of Cu(II) complexes with ethane-1,2-diamine as the amine part and pentane-2,4-dione and/or 1-phenylbutane-1,3-dione, pentane-2,4-dione and/or 1,1,1- trifluoropentane-2,4-dione, or 1,1,1-trifluoropentane-2,4-dione and/or 1-phenylbutane-1,3-dione as the ...
    Inorganic Chemistry,General Chemistry

  • Synthesis, magnetic, thermal and structural properties of Co(II), Ni(II) and Cu(II) complexes containing isophthalato ligands

    Jelena Rogan, Dejan Poleti, Ljiljana Karanović, Zvonko Jagličić (2011)
    A series of novel ternary Co(II), Ni(II) and Cu(II) complexes containing 2,20-dipyridylamine (dipya), 2,20-bipyridine (bipy), and 1,10-phenanthroline (phen), as aromatic diamine ligands, and dianion of isophthalic acid (ipht) have been prepared by ligand exchange reactions from diluted H2O/EtOH solutions. The complexes were characterized by elemental analysis, IR spectroscopy, magnetic susceptibility measurements and TG and DSC analysis. Three complexes, Cu(dipya)(ipht)H2O (1), Co(dipya)(ipht)2H2O (2) and Cu(ipht)(phen)2H2O (5) are polymeric with bis-monodentate ipht, while the other two complexes M(bipy)(ipht)4H2O, M@Co(II) (3) and ...
    комплекси прелазних метала, карбоксилатни лиганди, N-лиганди, кристална структура, магнетна својства

  • Metodologija proračuna sanacije klizišta šipovima

    Slobodan Ćorić, Dragoslav Rakić, Stanko Ćorić, Dušan Berisavljević (2022)
    Klizišta u Srbiji, u najvećem broju slučajeva, jako zavise od geoloških uslova u terenu i svako klizište ima svoje specifičnosti koje moraju da se odrede geotehničkim istraživanjima. Stoga su u radu prvo prikazane osnovne karakteristike klizišta u Srbiji, kao i postupci njihovog istraživanja. Zatim su prikazani proračuni sanacije klizišta vertikalnim šipovima. Metodologija proračuna je složena, jer podrazumeva interakciju klizišta i stabilizirajućih šipova. Prilikom određivanja bočne otpornosti tla oko šipova koristi se metoda Brinč Hansena koja uzima u obzir trodimenzionalne ...
    klizišta, geotehnička istraživanja, bočna nosivost šipova, interakcija klizišta i šipa, analiza stabilnosti

  • Metodologija određivanja vremena i putanje zagađivača na primeru zaštite izvorišta podzemnih voda

    Dušan Polomčić, Dragoljub Bajić, Vesna Ristić Vakanjac, Jelena Ratković, Marina Čokorilo Ilić (2018)
    Analiza vremena putovanja potencijalnog zagađivača do bunara izvorišta podzemnih voda predstavlja veoma bitan segment kod upravljanja i zaštite podzemnih voda. Ova metodologija se zasniva na simulaciji kretanja nereagujuće čestice sa podzemnim vodama i poroznom sredinom (“idealna” čestica). Rezultati hidrodinamičkog modela, kojim se vrši simulacija režima podzemnih voda, predstavljaju osnovu za model praćenja “idealne” čestice. Postoje različiti softveri koji se koriste u hidrogeološkoj praksi za analizu problema zagađivača. U ovom radu korišćen je numerički kod Modpath, dok je za simulaciju ...
    upravljnje podzemnim vodama, zaštita podzemnih voda, hidrodinamički model, metoda praćenja „idealne“ čestice, modflow, modpath.

  • Contribution to the geotechnical classification of municipal waste landfills in Serbia

    Dragoslav Rakić, Irena Basarić, Laslo Čaki, Slobodan Ćorić (2018)
    Management, Monitoring, Policy and Law, Nature and Landscape Conservation, Geochemistry and Petrology, Waste Management and Disposal,Geotechnical Engineering and Engineering Geology,Water Science and Technology,Environmental Chemistry,Environmental Engineering

  • Inhibitory effect of platinum and ruthenium bipyridyl complexes on porcine pancreatic phospholipase A2

    Tina Kamčeva, Jörg Flemmig, Bojana Damnjanović, Jürgen Arnhold, Aleksandar Mijatović, Marijana Petković (2011)
    Fosfolipaza pankreasa A2 (PLA2) igra važnu ulogu u ćelijskoj homeostazi kao iu procesu karcinogeneze. Efekti metalo-lekova koji se koriste kao hemoterapeutici na aktivnost ovog enzima nisu poznati. U ovom radu, interakcija između PLA2 svinjskog pankreasa i dva odabrana kompleksa prelaznih metala — tetrahloro(bipiridin) platine(IV) ([PtCl4(bipi)]) i dihloro (bipiridin) rutenijum(III)hlorida ([RuCl2(bipi)2) ]Cl)—proučavana je. Laserska desorpcija/jonizacija uz pomoć matriksa, vremenska masa spektrometrija (MALDI-TOF MS) i fluorescentna spektroskopija korišćeni su za analizu aktivnosti enzima u odsustvu i prisustvu metalnih kompleksa i za ...
    Metals and Alloys, Biochemistry, Biomaterials, Biophysics, Chemistry (miscellaneous)
    ... activity because this method is sufficiently sensitive and does not require any additional derivatization of the samples for the analysis. In addition, it allows analysis of both the substrate and the product of the enzyme-catalyzed reaction in a single spectrum. Moreover, alterations in the phospholipid ...
    ... important role in host-defense as well as clearance of necrotic tissues.25,26 MALDI-TOF MS has been already shown to be a powerful technique for the analysis of bipyridine metal complexes,27 and therefore it is used here as a method of first choice. Tested metal complexes affect the enzymatic aLaboratory ...
    ... platinum(IV) and [RuCl2(bipy)2]Cl dichloro- (bipyridine) ruthenium(III)chloride) were synthesized as described in the literature.28,29 Chemical analysis, UV-VIS and nuclear magnetic resonance (1H-NMR) spectral data of these complexes were in good agreement with those obtained in previous preparations ...

  • Differently shaped nanocrystalline (Fe, Y)3O4 and its adsorption efficiency toward inorganic arsenic species

    Biljana P Dojčinović, Boštjan Jančar, Lotfi Bessais, Aleksandar Kremenović, Nataša P Jović-Jovičić, Predrag T Banković, Dalibor M Stanković, Miloš Ognjanović, Bratislav V Antić (2019)
    Herein we report effects of partial substitution of Fe3+ by Y3+ in magnetite (Fe3O4) on morphology and inorganic arsenic species adsorption efficiency of the Fe3−xYxO4 nanoparticles formed. The series of Fe3−xYxO4 (x=0.00, 0.042 and 0.084, labeled as Y00, Y05 and Y10, respectively) was synthesized using co-precipitation followed by microwave-hydrothermal treatment (MW) at 200°C. With increase of yttrium content(xvalue), both the morphological inhomogeneity of the samples and the fraction of spinel nanorods as compared to spinel pseudospherical particles increased. By ...
    microstructure, microwave-hydrothermal synthesis, adsorption, magnetic nanoparticles, arsenic

  • Design of the Opencast Coal Mine Drmno Dewatering System

    Vladimir Pavlović, Dušan Polomčić, Tomislav Šubaranović (2014)
    Development of mining in the opencast mine Drmno from Kostolac basin in Serbia is carried out in the increasingly complex geological and hydro geological conditions with the decline of the coal seams to the alluvial part of Europe's largest river Danube. Greater depth and inflow of groundwater significantly increase costs for dewatering facilities construction with the requirement for optimizing of this more and more important surface mining process. Making decision on screen construction in the opencast mine with redesign ...
    dewatering system, groundwater, hydrodynamic model, dewatering wells, screen, reliability, environmental effects.

  • Human factor risk management procedures applied in the case of open pit mine

    Snežana Kirin, Aleksandar Sedmak, Wei Li, Miodrag Brzaković, Igor Miljanović, Ana Petrović, Simon Sedmak (2021)
    Risk management aims to provide a controlled work environment to ensure the safe operation of the high-risk systems. It is a dynamic process which work in a continual state of change. The issue of human factor risk and rules and regulations in open pit mine is a main focus of this paper in order to develop predictive models of behavior of workers in relation to compliance with the procedures and rules. Presented survey was conducted in open pit coal ...
    Upravljanje rizikom, ljudski faktor, bager sa kašikom, metod konačnih elemenata

  • Self-Engineering: Possibilities for Maintenance Operations in the Mining Machines Industry

    Steven Manders, Milorad Pantelić, Vladimir Milisavljević, Alberto Martinetti (2021)
    Self-engineering is a relatively new branch of knowledge that aims to understand how systems could “autonomously” re-configure or repair themselves without the intervention of the operators. A direct field of application is within the maintenance spectrum. Having systems or machines capable of self-detecting or even self-repairing could represent a game-changer, in capital asset fields such as the mining industry in particular. This paper aims to investigate the possible benefits and challenges of self-engineering / self-maintenance concerning mining machines, specifically bucket-wheel ...
    self-engineering, self-maintenance, maintenance operations, mining industry, bucket-wheel excavator, gearbox revitalization

  • Analiza pouzdanosti dozera angažovanih na površinskim kopovima RB Kolubara

    Filip Miletić, Dragan Milčić, Miloš Tanasijević, Miloš Milovančević (2021)
    U radu je izvršena uporedna analiza pouzdanosti transportnih sistema dozera koji rade na površinskim kopovima Rudarskog basena Kolubara. Period za koji je vršena analiza je prvih deset godina eksploatacije. Efikasnost tehnološkog procesa na otkopavanju korisne mineralne sirovine i otkrivke u velikoj meri zavisi od rada dozera. Iskorišćene su matematičke metode za aproksimaciju i identifikaciju zabeleženih vremena u radu, kako bi se dobili analitički pokazatelji pouzdanosti. Na ovaj način se bitno podiže kvalitet upravljanja procesom eksploatacije i održavanja mašina na ...
    dozeri, pouzdanost, kolubarski ugljeni basen
    ... pouzdanost, kolubarski ugljeni basen Abstract: The paper presents a comparative reliability analysis of the dozers transport systems which working on the open pit mines of the Kolubara Mining Basin. Analysis period is first ten years of exploitation. Efficiency of process on excavation of mineral raw ...
    ... arski, sa parametrom oblika i parametrom razmere η. [7] Parametri raspodele mogu se odrediti analitički, metodom najmanjih kvadrata (Regression analysis) [8] i grafički. Analitički postupak daje nešto tačnije rezultate. Primenom grafičkih metoda može se oceniti tačnost razvijenog modela zakona raspodele ...
    ... mašinskih delova i sistema u okruženju Microsoft Excel, Infoteh–Jahorina Vol. 10, Ref. C-8, p. 273-277, Mart 2011; [8] Ashish S., Muni S. Regression analysis - Theory, Methods, and Applications, Springer-Verlag New York, 1990.; [9] Milčić D. Pouzdanost mašinskih sistema, Univerzitet u Nišu, Mašinski fakultet ...

  • Surface functional groups and degree of carbonization of selected chars from different processes and feedstock

    Marija Ilić, Franz-Hubert Haegel, Aleksandar Lolić, Zoran Nedić, Tomislav Tosti, Ivana Sredović Ignjatović, Andreas Linden, Nicolai D. Jablonowski, Heinrich Hartmann (2022)
    The knowledge ofthe structural and chemical properties of biochars is decisive for their application as technical products. For this reason, methods for the characterization of biochars that are generally applicable and allow quality control are highly desired. Several methods that have shown potential in other studies were used to investigate two activated carbons and seven biochars from different processes and feedstock. The chars were chosen to cover a wide range of chemical composition and structural properties as a hardness ...
    Biougalj, različiti procesi dobijanja, različite sirovine, površinski aktivne grupe, x-ray, FT-IR,XPS
    ... of K2p. https://doi.org/10.1371/journal.pone.0277365.t006 corresponds to the abundance found by chemical analysis and by XRD. The deviation of the O/C ratio from XPS and element analysis (Fig 2) was largest for the activated carbons and PW?700g. The lower O/C ratio for AC2 obtained by XPS can ...
    ... 100%) and the determination of ash forming elements. This complete analysis is the base for understanding the properties of the chars. In special cases, as for the presence of phosphoric acid in AC2, additional chemical analysis might be necessary to elucidate the true composition. X-ray diff ...
    ... spectroscopic methods was found to be suitable for the quality control of all types of chars. The most valuable results were obtained by chemical analysis that, however, required the complete determination of the main elements, including that of oxygen, and of inorganic components for adequate results ...