Претрага

Упит dcterms_subject_txt:production optimisation

48 items

  • Productivity improvement with use of beam gas compressor: pilot test in Southeastern Europe mature field

    Bojan Martinović, Dušan Danilović, Branko Grubač, Robert Fadiga (2022)
    Most of the wells in the oilfield Turija are operating with sucker rod pumps, where casing pressure at around 15 bar, and with marginal production rates. The high value of casing pressure indicates high pressure on the face of the formation and depends directly on well productivity. In addition, with increasing value of the casing pressure gas column in the annulus is moving the dynamic fluid level near pump intake and more gas is entering the pump, it results ...
    beam gas compressor, BGC, increase productivity, sucker rod pump, SRP, mature field, artificial lift, production optimisation

  • Optimisation of underground mine decline development system using genetic algorithm

    Zoran Gligorić, Aleksandar Ganić, Rade Tokalić, Aleksandar Milutinović (2014)
    ... slope that can be handled by loaded mine truck in a safe way. Decline optimisation is concerned of determination of locations of SBP and UMCP. A general design optimisation problem is formulated as follows: Optimisation of underground mine decline ... ...
    ... 2023-10-14 03:40:59 Optimisation of underground mine decline development system using genetic algorithm Zoran Gligorić, Aleksandar Ganić, Rade Tokalić, Aleksandar Milutinović Дигитални репозиторијум Рударско-геолошког факултета Универзитета у Београду [ДР РГФ] Optimisation of underground mine ...
    ... constraints can be treated by different strategies. The penalty function technique is used to transform the constrained optimisation problem to unconstrained optimisation problem by penalizing the constraints and forming a new objective function as follows (Ali, 2014):   ( ) if feasible ...

  • Hybrid Model for Optimisation of Waste Dump Design and Site Selection in Open Pit Mining

    Aleksandar Doderovic, Svetozar-Milan Doderovic, Sasa Stepanovic, Mirjana Bankovic, Dejan Stevanovic (2023)
    Waste management is an unavoidable technological operation in the process of raw material extraction. The main characteristic of this technological operation is the handling of large quantities of waste material, which can amount to several hundred million cubic metres. At the same time, this operation must comply with all administrative and environmental standards. Therefore, optimising waste rock management (particularly haulage and dumping) has the potential to significantly improve the overall value of the project. This paper presents a hybrid ...
    projektovanje odlagališta i izbor lokacije, hibridni model, optimizacija, genetski algoritam

  • Design and optimisation of laser scanning for tunnels geometry inspection

    Pejić Marko, Božić Branko, Abolmasov Biljana, Gospavić Zagorka (2013)

  • Corrigendum to „Design and optimisation of laser scanning for tunnels geometry inspection“

    Pejić Marko, Božić Branko, Abolmasov Biljana, Gospavić Zagorka (2013)

  • Uncertainty in open pit optimisation

    Kolonja Božo, Stevanović Dejan, Pešić Georgiadis Milica, Banković Mirjana, Kolonja Ljiljana (2015)

  • Optimisation the final countur of the open pit North mining district using the software package Whittle

    Kržanović Daniel, Stevanović Dejan, Rajković Radmilo, Jovanović Milenko, Žikić Miodrag, Stojadinović Saša (2016)

  • Application of the VIKOR and FAHP multi-criteria optimisation methods for choosing the optimal groundwater control system: case of pumping station Bezdan 1 (Serbia)

    Bajić Dragoljub, Polomčić Dušan, Ristić Vakanjac Vesna, Ratković Jelena, Čokorilo Ilić Marina (2017)

  • Long-term planning methodology for improving wood biomass utilization

    Vladimir Vukašinović, Dušan Gordić, Marija Živković, Davor Koncalović, Dubravka Živković (2019)
    The insufficiently developed forest management system is often followed by undeveloped forest resources supply chain and insufficient institutional support. These cause inefficient usage of fuel-wood as well as huge amounts of unused forest residues. In order to achieve optimal and long-term sustainable utilisation of biomass, an original methodology based on the interaction of mathematical optimization and backcasting approach has been developed. Mathematical optimization is used for both generation and consideration of techno-economic parameters of the forest biomass supply chain. ...
    Long-term planning methodology, Forest biomass, MINLP, Backcasting

  • Mine ventilation system planning using genetic algorithms

    Nikola Lilić, Ranka Stanković, Ivan Obradović (1997)
    The most common problem in contemporary mining practice related to the planning and analysis of ventilation systems is the optimization of partially regulated air distribution in mine ventilation networks. This paper presents a two step optimization procedure for partly regulated air distribution in mine ventilation networks. The first step is the determination of air distribution in all branches using the well known Hardy-Cross method. In the second step the distribution and parameters of air flow regulators with minimum engaged ...
    coal, lignite, and peat; ventilation systems; coal mining; underground mining; ventilation; mathematical models; design; air flow; optimization; calculation methods

  • Novi model za postizanje optimalne proizvodnje na naftnom polju Amal

    Elnori Elmabrouk Ali Elhaddad (2015-04-16)
    Doktorskom disertacijom analizirani su i proučavani problemi proizvodnje nafte iprimenjene metode za njihovo rešavanje na naftnom polju Amal. Ukratko jeprikazana proizvodnje nafte u Libiji, njene karakteristike i rezerve, da bi se videoznačaj ovog naftnog polja.Utvrđeno je da su na naftnom polju Amal ključni problemi koji prate procesproizvodnje taloženje parafina, pojava slojnog peska, neefikasan rad gasliftsistema, neefikasna desalinizacija nafte i ekološki problemi. Proizvodniproblemi, pojedinačno i više njih zajedno, na nekim bušotinama uzrokovali susmanjenje proizvodnje nafte od 40 do 75%. Zbog ...
    nafta, proizvodnja, optimizacija, Amal, Libija
    ... reflected in the original model for a solution of the production problems at the Amal oilfield. The proposed solutions can improve production problems solution, provide more efficient management of the production process and increase oil production. In addition to its importance for the Amal oilfield ...
    ... MODEL FOR ACHIEVING OPTIMUM PRODUCTION AT AMAL OILFIELD Summary In this doctoral dissertation, it has analyzed the problems of oil production and application of methods for their solutions at the Amal oilfield. It has also provided a brief presentation of oil production in Libya, its characteristics ...
    ... at some oil wells, caused a decrease in production of 40% up to 75%. It was necessary to take additional measures and actions in order to solve the production problems so that they could not become worse and cause further decrease in oil production. Based on the characteristics of the Amal ...

  • Application of Lignite Combustion Waste Slag Generated in Heating Plants as a Partial Replacement for Cement. Part II: Physical–Mechanical and Physical–Chemical Characterization of Mortar and Concrete

    Milan Kragović, Nenad Ristić , Jelena Gulicovski, Andrijana Nedeljković, Snežana Pašalić, Ivica Ristović, Marija Stojmenović (2021)
    sagorevanje lignita, otpadna šljaka, zamena cementa, proizvodnja maltera i betona, fizičko-mehanička i fizičko-hemijska karakterizacija
    ... 12. Rivera, J.F.; Cristelo, N.; Fernández-Jiménez, A.; de Gutiérrez, R.M. Synthesis of alkaline cements based on fly ash and metallurgic slag: Optimisation of the SiO2/Al2O3 and Na2O/SiO2 molar ratios using the response surface methodology. Constr. Build. Mater. 2019, 213, 424–433. [CrossRef] 13. ...
    ... For that purpose, the optimal conditions for the practical application in mortar and concrete production are defined. Tests related to the use of waste slag as a partial replacement for cement in the production of mortars and concrete are performed in accordance with certain standards, and the detailed ...
    ... construction industry. The different amounts of cement (10%, 15%, 20% and 25%) were replaced with waste slag and silica fumes in mortars and concrete production. Detailed physical–mechanical characterization was performed on the mortar and concrete samples according to standard procedures. Test results ...

  • Design of a sucker rod pumping system

    Ana Ponoćko (2024)
    For a long time in the history of oil production, sucker rod pumps have been the first and in many cases the only choice when it comes to mechanical extraction methods. Proper selection of each individual element of the system enables optimization, which entails benefits in the form of increased efficiency and reduced costs. The first part of the paper presents the underground and surface equipment of the rod pump and describes the operation of the entire system. The ...
    sucker rod pump, fluid production, mechanical extraction methods,, Prosper, QROD, RODSTAR
    ... calculate expected production rates, pump intake pressure, and pump condition for any rod pumping system, as well as determining the maximum achievable production rate and more. 36 Unlike traditional trial-and-error approaches, RodStar lets you input a target production rate and simultaneously ...
    ... found in the reservoir under a certain pressure that allows the fluid to move from the reservoir into the well and then through the production system. If the production of fluid relies solely on the natural energy of the reservoir, this method of exploitation is called an eruptive method. When the ...
    ... enable the flow of fluid through the well, pipeline, and surface equipment, when production has reached a minimum economically viable value additional energy must be supplied to continue extraction. If fluid production is achieved using additional energy, this method of exploitation is called a ...

  • Application of stochastic models for mine planning and coal quality control

    Dejan Stevanović, Božo Kolonja, Ranka Stanković, Dinko Knežević, Mirjana Banković (2014)
    ... Such an ap- proach requires a prior knowledge of the coal quality of planned mining blocks. Coal homogenization is one of mostly used options for optimisation of sulfur emis- sions from desulfurization power plants [2]. However, decisions about coal homogenization must deal with uncertainty and variability ...
    ... 4, pp. 1361-1372 1363 Figure 1. Long-term and operational variability of SO2 grade mine on the basis of predicted information.The standard optimisation technique widely used in many industrial applications is the linear and integer programming 12 . Models involve optimi- zation of a quantity usually ...
    ... Models for Mine Planning ... 1364 THERMAL SCIENCE: Year 2014, Vol. 18, No. 4, pp. 1361-1372 mine on the basis of predicted information.The standard optimisation technique widely used in many industrial applications is the linear and integer programming 12 . Models involve optimi- zation of a quantity usually ...

  • Uporedni prikaz proizvodnje električne energije iz uglja zemalja Evrope sa najvećim udelom: politika i projekcija proizvodnje

    Predrag Jovančić, Dragan Ignjatović, Stevan Đenadić (2022)
    Energetski razvoj zemalja Evrope decenijama je bio baziran na uglju. Instalisana snaga svih energetskih kapaciteta koji su zasnovani na uglju je preko 2000 GW. Ugalj je i dalje od bitnog značaja za dobijanje električne energije u Evropi. I pored toga što postoji veliki potencijal uglja, trend je smanjenja proizvodnje električne energije iz uglja do 2050. godine. Imajući u vidu Zelenu agendu i politiku EU, zemlje Evrope se okreću obnovljivim izvorima energije. Srbija u okviru obnovljvih izvora ima potencijala prevashodno ...
    ugalj, električna energija, 2050. godina, projekcija proizvodnje

  • Eksploatacioni učinci ugljenih sistema na površinskom kopu Tamnava–Zapadno polje

    Marko Lazić, Filip Miletić, Milena Lekić, Veljko Rupar, Željko Petrović, Lazar Žujović (2021)
    U radu su analizirani eksploatacioni učinci ugljenih sistema na površinskom kopu Tamnava–Zapadno polje. Period analize je prvih šest meseci tekuće godine. Analiza je vršena sa aspekta ostvarene proizvodnje, kvaliteta uglja, efektivnog vremena rada, kapacitetnog i vremenskog iskoršćenja i zastoja sistema. Za poređenje podataka različitih parametara koji po svojoj prirodi nisu međusobno uporedivi, u radu su korišćene metode višekriterijumskog odlučivanja.
    proizvodnja uglja, zastoji, metode višekriterijumskog odlučivanja
    ... in the aspect of reached production, coal quality, effective working time, capacity and time utilization and system stoppage using multicriteria decision–making methods. Ključne reči: proizvodnja uglja, zastoji, metode višekriterijumskog odlučivanja Keywords: coal production, stoppage, multicriteria ...

  • Развој хибридног модела за оптиматизацију завршне контуре одлагалишта у површинској експлоатацији лежишта минералних сировина

    Aлександар Додеровић (2024)
    Површинска експлоатација минералних сировина захтијева претходно откопавање значајних( милионских) количина јаловине, које је неопходно транспортовати до локације на којој ће сеона трајно одложити. Традиционални приступ избора локације и дизајна одлагалишта се карактерише парцијалним приступом, заснованом на анализи неколико водећих критеријума као и на личном искуству инжењера, често занемарујући синергетски ефекат осталих утицајних фактора Технолошке операције које се односе на манипулацију јаловином, међу којима предњачи транспорт, генеришу највећи дио трошкова у површинској експлоатацији. Такође, цјелокупан процес експлоатације додатно је ограничен ...
    оптимизације завршне контуре одлагалишта, хибридни модел, површинска експлоатација, генетски алгоритам

  • An Experimental Investigation of the Environmental Risk of a Metallurgical Waste Deposit

    Jasmina Dedić , Jelena Djokic , Jovana Galjak, Gordana Milentijević, Dragan Lazarevic, Živče Šarkočević, Milena Lekić (2022)
    The aim of this study is to investigate the environmental risk of long-term metallurgical waste disposal. The investigated site was used for the open storage of lead and zinc waste materials originating from a lead smelter and refinery. Even after remediation was performed, the soil in the close vicinity of the metallurgical waste deposit was heavily loaded with heavy metals and arsenic. The pollutants were bound in various compounds in the form of sulfides, oxides, and chlorides, as well ...
    otpad od proizvodnje olova, remedijacija, rizik po životnu sreinu, BCR sekvencijalna ekstrakcija

  • Application of Gel for Water Shutoff: A Case Study of Kelebija Oil Field

    Irina Zahirovic, Petar Skrobonja, Dušan Danilović (2022)
    This paper focuses on the results of water shutoff operations using DSGA polymer gel in the Kelebija oil field. The methodology of candidate wells selection and the manner of performing the operation will also be included. The Kelebija oil field is characterized by a complex reservoir system with heterogeneous layers of different permeability and dual porosity, which led to the early breakthrough of water. For the last 25 years, average water cut was above 90%. Implementation of water shutoff ...
    intervención de pozos petroleros, reservoir characterization, production control, well logging, downhole intervention, enhanced recovery, complex reservoir, reservoir surveillance, water shut-off, upstream oil & gas

  • Анализа утицаја искоришћења у преради на резултате оптимизације површинских копова

    Стефан Митић (2024)
    Одређивање оптималних граница површинског копа је сложен и итеративни процес који захтева мултидисциплинарну експертизу, софистициране технике анализе и пажљиво разматрање геолошких, рударских, економских,техничких, еколошких и друштвених фактора. Оптимизација подразумева генерисање серије шкољки, површинског копа на основу различитих фактора прихода (Revenue factor) са итеративним кораком промене цене метала у односу на базну цену. Свака генерисана шкољка представља инкрементално повећање запремине резерви према инкременталном повећању продајне цене метала. Велики број техно -економских фактора утиче на овај процес, и промена сваког од њих ...
    оптимизација површинског копа, анализа границе копа, оптимална контура копа, лежиште Бувач, профит, искоришћење у преради, трошкови прераде руде
    ... Planning and Equipment Selection. 4. Coombes J, 2004. Resource Estimation. :Snowden Mining Industry Consultants. 5. Dagdelen K., 2001. Open Pit Optimisation - Strategies for Improving Economics of Mining Projects through Mine Planning, International Mining Congress and Exhibition of Turkey 6. David ...
    ... by use of Genetic Algorithms. Nottingham, Symposium on Artificial Intelligence in the Minerals Sector. 8. Githiria J., 2016. Cut-off grade optimisation to maximise the net present value using whittle 4X. Int. J. Mining and Mineral Engineering, 7(4). 9. Hall G., 2004. Multi-mine Better Than Multiple ...
    ... pyoapcmay. beorpay, Pynapcko-I eomomku (aky1TeT. 21.M.L. Smith, 2001. Using Milawa/4X as a Starting Solution for Mixed Integer Programming Optimisation. Perth, s.n. 22. Mario E. Rossi ; Clayton V. Deutsch, 2014. Mineral Resource Estimation. Dordrecht: Springer Science+Business Media. 23.Muznenko ...